Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 27

Страница: 27 / 119

FIGURE 11 Attaching the adhesive feet

Attach the four adhesive feet to the bottom of the device. If installing multiple devices, attach the adhesive feet to each device.

2. Set the device on a flat desktop, table, or shelf near an AC power source. Make sure that adequate ventilation is provided for the

system. A 7.62 cm (3 in.) clearance is recommended on each side.

3. If installing a single device only, proceed to

Powering on the system

on page 76. If installing multiple devices, place each

device squarely on top of the one below.

Installing the device into a rack

This section describes the procedures you use to mount the device into a rack.

The Brocade ICX 7250 can be installed in a 2-post or 4-post rack.

The device ships with a 2-post rack. To use the rack that ships with the product, refer to

Installing the device using the included two-post

rack mount kit

on page 28.

To install the product into a four-post rack, you can order one of two four-post rack kits with the part number XBR-R000295 or
XBR-000296. For the procedures to install these kits, refer to

Installing the 1U, 1.5U, and 2U Universal Kit for Four Post Racks (XBR-

R000295)

on page 29 and

Installing the Universal Four-Post Rack Kit (XBR-R000296)

on page 43.

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды