Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 119

background image

TABLE 10 Installation tasks (continued)

Task number

Task

Where to find more information

4

Once the device is installed, plug the device into
a nearby power source that adheres to the
regulatory requirements outlined in this manual.

Powering on the system

on page 76 section

5

Verify that the device is working properly by
plugging it into a power source and verifying that
it passes the self test.

Verifying proper operation

on page 77 section

Installation precautions

Follow all precautions when installing a device.

General precautions

DANGER

All fiber-optic interfaces use Class 1 lasers.

CAUTION
Do not install the device in an environment where the operating ambient temperature might exceed 50°C (122°F).

CAUTION
Make sure the airflow around the front, sides, and back of the device is not restricted.

Lifting precautions

DANGER

Make sure the rack housing the device is adequately secured to prevent it from becoming unstable or falling over.

DANGER

Mount the devices you install in a rack as low as possible. Place the heaviest device at the bottom and progressively place
lighter devices above.

Power precautions

CAUTION
Use a separate branch circuit for each power cord, which provides redundancy in case one of the circuits fails.

CAUTION
Ensure that the device does not overload the power circuits, wiring, and over-current protection. To determine the possibility of
overloading the supply circuits, add the ampere (amp) ratings of all devices installed on the same circuit as the device. Compare
this total with the rating limit for the circuit. The maximum ampere ratings are usually printed on the devices near the input
power connectors.

DANGER

Disconnect the power cord from all power sources to completely remove power from the device.

Installing the EPS4000

Brocade ICX 7250 Switch Hardware Installation Guide

68

53-1003898-02

«
...
66
67
68
69
70
...
»

Содержание ICX 7250
























































































































Отзывы:

Нет отзывов

Похожие инструкции для ICX 7250

Бренд: Nectarine Health Страницы: 9

Бренд: Lantronix Страницы: 40

Бренд: Lantronix Страницы: 2

SISTP1040-551-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 2

SISPM1040-3 L Series

Бренд: Lantronix Страницы: 2

SISPM1040 L3 Series

Бренд: Lantronix Страницы: 36

SecureLinx Spider

Бренд: Lantronix Страницы: 18

Бренд: Lantronix Страницы: 8

Бренд: Lantronix Страницы: 6

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 272

Xpress-Pro SW 52000

Бренд: Lantronix Страницы: 8

3C63100-AC-C - PathBuilder S600...

Бренд: 3Com Страницы: 232

ETHERLINE ACCESS U04TP01T

Бренд: LAPP Страницы: 16

RoamAbout RBT-4102-BG

Бренд: Enterasys Страницы: 72

Бренд: SIIG Страницы: 17

Бренд: FCI Страницы: 12

Бренд: Micrel Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды