manualshive.com logo in svg

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Поделиться
Скачать
Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 77

2. Attach the AC power cord to the AC connector on the rear panel.
3. Insert the power cord plug into a 100V-240V outlet.

NOTE
To turn the system off, unplug the power cord or cords.

Connecting devices to the external power supply

Complete the following steps to connect devices to the external power supply.

1.

Connect one end of the AC cord to the AC receptacle on the device, and the other end to a grounded power outlet.

2. Connect one end of an EPS cord to the external power receptacle on the device, and the other end to an available receptacle on

the external power supply.

3. Repeat Step 

Step 1

and Step 

Step 2

to connect up to the allowable maximum number of devices to the external power supply.

The maximum number of devices will depend on both the number of power supply units in the EPS4000 and whether you use
1:1 cords or 1:2 cords.

4. Connect one end of the AC cord to the AC receptacle on the external power supply, and the other end to a grounded power

outlet.

5. Check the LEDs on the external power supply to ensure proper operation with the devices.

Verifying proper operation

After you have installed an external power supply, verify that the device is working properly by plugging it into a power source and
verifying that it passes the self test.

1.

Connect the power cord supplied with the device to the power connector on the power supply on the rear of the device.

2. Insert the other end into a properly grounded electrical outlet.
3. Verify that the LED for the power supply is green.
4. Verify proper operation by observing the LEDs.

LEDs for linked ports will come on during the boot process, and then all LEDs will go off. Once the boot sequence is complete,
LEDs for linked ports will come on again.

EPS4000 external power supply technical specifications

System specifications

System component

Description

Enclosure

1U; 19-inch rack-mountable or desktop

Power inlet

C14 for AC power

Power outlet

Custom connector for DC power to all ICX 7250 devices except ICX 7250-24G

Power supply unit (PSU)

Up to four RPS17, field-replaceable units (FRU)

Fans

One fan per installed RPS17

Cooling

Forced air circulation

Front-to-back airflow

System architecture

External power supply (also referred to as external power shelf)

Installing the EPS4000

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

77

Содержание ICX 7250
























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды