Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 73

Страница: 73 / 119

Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack) to act
as ground.

2. Remove the four screws that hold the PSU slot cover in place.

FIGURE 50 Installing an RPS17 PSU

RPS17 PSU slots (3 populated, 1 available)

2. Screws

NOTE
If you are replacing an RPS17 PSU, you must uninstall a PSU. Refer to

Uninstalling an RPS17 PSU

on page 73.

3. Remove the new PSU from the protective packaging.
4. Gently insert the PSU into the slot until it clicks into place.

Uninstalling an RPS17 PSU

You can uninstall an RPS17 PSU from the EPS4000while the device is powered on and running.

NOTE
While uninstalling a PSU, wear an ESD wrist strap.

DANGER

For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.

Perform the following steps to uninstall an RPS17 PSU.

Put on the ESD wrist strap and ground yourself by attaching the clip end to a metal surface (such as an equipment rack) to act
as ground.

2. Lift the PSU latch and gently slide the PSU out from the slot.

Installing the EPS4000

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды