Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 19

Страница: 19 / 119

System status LEDs

The following figure shows the system status LEDs for ICX 7250 models.

FIGURE 9 System status LEDs for ICX 7250 models

ICX 7250-24G LEDs

2. ICX 7250-24, ICX 7250-24P, ICX 7250-48 LEDs

3. ICX 7250-48P LEDs

TABLE 4 System status LEDs

LED

Condition

Status

PWR

Green

Power supply is operating normally.

Yellow

Power supply fault.

Off

Power supply off.

EPS1 and EPS2 (for supported models)

Green

EPS1 and EPS2 power supplies are operating
normally.

Yellow

EPS1 and EPS2 power supply fault.

Off

EPS1 and EPS2 off or not present.

DIAG

Flashing Green

System self-diagnostic test in progress. System
reloads automatically.

Steady Yellow

System self-diagnostic test has detected a fault.
(Fan, thermal, or any interface fault.) The user
must reload the system.

Green

The device is the Active controller. Flashing
indicates the system is initializing.

Yellow

Indicates the device is the Standby controller.
Flashing indicates the system is in Master
arbitration or selection state.

Off

Device is operating as a stack member, or is in
standalone mode.

UPLINK

Green

Uplink port is operating normally.

Off

Uplink has failed or there is no link.

DOWNLINK

Green

Downlink port is operating normally.

Off

Downlink has failed or there is no link.

1-10+ (ID)

Green

Indicates the switch ID in the stack.

Overview

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды