Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 50

Страница: 50 / 119

FIGURE 31 Attaching the rear brackets to the extensions

Rear brackets

Screws, 6-32 x 1/4-in., panhead Phillips

Attaching the rear brackets to the rack posts

Complete the following steps to attach the rear brackets to the rack posts.

Attach the right rear bracket to the right rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts, as
shown in

Figure 32

. Use the upper and lower holes in the bracket.

2. Attach the left rear bracket to the left rear rack post using two 10-32 x 5/8-in. panhead screws and two retainer nuts. Use the

upper and lower holes in the bracket.

3. Tighten all the 10-32 x 5/8-in. screws to a torque of 25 in-lb (29 cm-kg).

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды