Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 14

Страница: 14 / 119

FIGURE 3 ICX 7250-24G rear panel

FIGURE 4 ICX 7250-48 rear panel

Network and management interfaces

Each device includes the following management interfaces.

∙

Console management interface (mini-USB port)

∙

Out-of-band management interface (RJ-45 port)

The ports are located on the front panels of the devices. The following figure shows an example of a 48-port device.

FIGURE 5 Network and management interfaces on a 48-port model

Out-of-band management port (RJ-45)

2. Console port (mini-USB)

3. Slot 1 (10/100/1000 Mbps ports - RJ-45)

4. Slot 2 (SFP+ uplink or stacking ports)

5. Reset button - not a management interface, shown for reference only.

The reset button allows you to restart the system without switching the power supply off and on or using the CLI. When the
reset button is pressed, the system resets and the software is reloaded.

6. USB port

NOTE
24-port devices have similar front panels. For the ICX 7250-24G, the slot 2 ports are SFP ports.

Overview

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды