Brocade Communications Systems ICX 7250 Скачать руководство пользователя страница 57

Страница: 57 / 119

FIGURE 38 Attaching the rear brackets to the front rack posts

Screws, 10-32 x 5/8-in., panhead Phillips

Retainer nuts, 10-32

Wall mount installation

NOTE
You need a #2 Phillips screwdriver, a hammer, and a drill for wall mount installation.

Brocade recommends that you wall mount the device with the port side down.

Complete the following steps to mount the device to a wall.

DANGER

This equipment is suitable for mounting on concrete or other noncombustible surfaces only.

Attach the four adhesive feet to the bottom of the device.

2. Using a Phillips screwdriver, attach the wall mount brackets to the sides of the device using four #6-32 sink-head screws on

each side.

Installation

Brocade ICX 7250 Switch Hardware Installation Guide

53-1003898-02

Содержание ICX 7250
























































































































Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды

Brocade Communications Systems ICX 7250, Руководство по установке оборудования

Результаты поиска

Содержание ICX 7250

Отзывы:

Похожие инструкции для ICX 7250

Бренды по названию

Популярные бренды