To configure traffic counters for outbound traffic in a specific port region, enter a command such as the
following.
device(config)#transmit-counter 1 port 1 region vlan all prio all enable
The above command creates and enables traffic counter 1 on all ports that are in the same port region
as port 1. The device will count the number of packets transmitted in this port region that belong to any
VLAN and have any assigned priority queue.
Syntax:
[no] transmit-counter
counter-ID
port
[
slotnum
/
]
port-num
{
only
|
region
}
vlan
{
vlan-ID
|
all
}
priority
{
priority-queue
|
all
}
enable
Enter the
no
form of the command to remove the outbound traffic counter.
The
counter-ID
parameter identifies the traffic counter. You can configure up to 64 traffic counters.
Enter a number from 1 - 64.
The
slotnum
parameter is required on chassis devices.
The
port-num
parameter is the port number to which enhanced traffic counters will apply. Enter the port
number followed by
only
to apply the enhanced traffic counter to a specific port, or enter the port
number followed by
region
to apply the enhanced traffic counter to all of the ports in the port region.
The
vlan-ID
parameter identifies the VLAN ID for which outbound traffic will be counted. Enter a number
from 0 - 4095 or enter
all
to indicate all VLANs.
The
priority-queue
parameter identifies the 802.1p priority queue for which traffic will be counted. Enter
a number from 0 - 7 or enter
all
to indicate all priority queues.
Displaying enhanced traffic counter profiles
To display the details of the traffic counters configured on your device, enter the
show transmit-
counter profiles
command. The following shows an example output.
device#show transmit-counter profiles
Tx Counter Port(s) Vlan Id Priority Device Set
1 1 - 12 All All Dev 0 Set0
4 18 1 7 Dev 1 Set0
10 13 - 24 100 All Dev 1 Set1
Displaying enhanced traffic counter statistics
To display the traffic counters for outbound traffic, enter the
show transmit-counter profiles
command.
NOTE
Once the enhanced traffic counters are displayed, the counters are cleared (reset to zero).
The following shows an example output.
device#show transmit-counter values 1
Transmit Queue Counter Values for Counter 1:
Transmitted Frames:
Known Unicast : 17204
Multicast & Unknown Unicast : 2797
Broadcast : 5
Dropped Frames:
Bridge Egress Filtered : 2
Congestion Drops : 0
device#show transmit-counter values 4
Transmit Queue Counter Values for Counter 4:
Transmitted Frames:
Displaying enhanced traffic counter profiles
FastIron Ethernet Switch Administration Guide
237
53-1003625-01
Содержание FastIron
