Brandt SB4000 Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 145

background image

65

4.4.1 BOTTOM FILLING THE MAIN TANK WITH THE NURSE TANK PUMP

1. Connect the transfer line from the nurse tank to the 2" male coupler on the Bottom Fill valve. Be certain that all
hoses and fittings are clean before the water transfer is made.

2. Open the Bottom Fill valve, Pump
Shutoff valve and the Tank Shutoff
valve. Close all other valves.

3. Start the nurse tank pump.

4. When the water transfer is
complete, close the Bottom Fill
valve. Disengage the nurse tank
pump.

NOTE: A typical 5 horse power 2"
nurse tank pump should pump
between 360 to 450 L/min (80 to
100 Imperial gpm, 100 to 120 US
gpm.)

4.4.2 FILLING THE MAIN TANK WITH THE SPRAYER PUMP

1. Connect the transfer line from the nurse tank to the 2" male coupler on the Bottom Fill valve. Be certain that the
hoses and fittings are clean before the water transfer is made.

2. Open the Bottom Fill valve, the Throttling valve, the Transfer valve and the Tank Shutoff valve. Close the Pump
Shutoff valve.

3. Start the sprayer pump.

4. When the water transfer is complete, close the Transfer valve. Open the Pump Shutoff valve.

NOTE: The typical pump flow rate should be between 220 to 310 L/min (50 to 70 Imperial gpm, 60 to 80 US
gpm per minute).

IMPORTANT: When using the sprayer to apply liquid fertilizer, because of the high weight of the fertilizer

(approx. 13 lbs/Imp. gallon), the tank

MUST NOT

be filled to more than 80% of the tank’s

capacity. This measurement calculates to 4850 Litres (1065 Imp. gallons, 1280 US gallons).
Failure to follow this procedure could result in severe damage to the sprayer.

Jet Agitators

Main Tank Sump

Transfer Valve

Throttling Valve

Agitator
Valve

Bottom Fill Valve

Pump

Pump Shutoff Valve

Tank Shutoff Valve

Electric Regulating Valve

F

IG

. 4.5 B

ASIC

P

LUMBING

L

AYOUT

To Spray Pipes

IMPORTANT:

Never run a centrifugal pump dry for more than a few seconds. Fluid is required at all times

to cool the pump, preventing pump seal damage. If the pump will not prime or runs out of fluid,
shut it off promptly.

Keep the mix and fill tank suction valve closed at all times unless in use. The sprayer pump must be primed and
pumping before opening the mix and fill tank suction valve to prevent tank overflow and loss of chemical.

«
...
74
75
76
77
78
...
»

Содержание SB4000


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SB4000

Бренд: Earlex Страницы: 18

Бренд: PVA Страницы: 8

6002 Big B.O.S.S.

Бренд: Mytee Страницы: 16

Бренд: IRONSIDE GARDEN Страницы: 11

Бренд: Magnum Страницы: 32

Бренд: WAGNER Страницы: 48

Бренд: SAMES KREMLIN Страницы: 5

EZ TILT POWER PAINTER PRO

Бренд: WAGNER Страницы: 22

Бренд: Tarmo Страницы: 7

Бренд: Bort Страницы: 24

CLEANline 333 FA

Бренд: Solo Страницы: 9

Бренд: WERKU Страницы: 40

Бренд: Kremlin-Rexson Страницы: 6

Бренд: Kremlin-Rexson Страницы: 12

Бренд: Fimco Страницы: 10

Бренд: Joto Страницы: 28

RapidLine SVL0020L0038

Бренд: Rapid Spray Страницы: 4

Бренд: ZIPPER MASCHINEN Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды