manualshive.com logo in svg

BENDIXKing 89000016-130, Руководство по установке системы, Страница: 159 / 181

Поделиться
Скачать
BENDIXKing 89000016-130 Скачать руководство пользователя страница 159

SYSTEM INSTALLATION MANUAL

89000016

TROUBLESHOOTING

1.

General

A.

Overview

(1)

This section provides information for troubleshooting problems that occur after KGX
installation. This section contains information on how to use the KGX LEDs and KGX control
panel (if installed) to troubleshoot installation problems. Refer to the CONFIGURATION,
CALIBRATION, AND CHECKOUT section to setup and configure the system.

2.

KGX LED Troubleshooting Procedure

A.

General

(1)

Table 4001 is a quick reference troubleshooting guide using the KGX LEDs.

Table 4001. Troubleshooting Guide

Problem

Potential Cause

Troubleshooting

No LED activity

No power

Verify power is turned on.
Check power connections to unit.

TX LED not active

Unit is not transmitting
ADS-B messages

Check antenna connections.
Check KGX control panel system messages.

RX LED not active

Unit is not receiving
ADS-B messages

Check antenna connections.
Check KGX control panel system messages.

ST LED is on

A fault with the unit

Check KGX control panel system messages.

ST LED is flashing quickly

GPS fault has occurred

Check GPS connection/configuration.
Check KGX control panel system messages.

GPS LED is flashing
slowly

GPS is acquiring satellites

Allow 2 to 3 minutes for GPS tracking.
Check GPS antenna.
Check GPS for problems.

GPS LED is off

GPS not communicating

Check GPS connection.
Check installation configuration.

GPS LED is flashing
quickly

GPS is reporting a fault

Check GPS for fault.

B.

UAT Status LED/Discrete Fault Indications

(1)

The status LED/discrete is an indicator of a fault reported by the KGX. The status LED is
visible on the KGX or the discrete can be connected to a cockpit annunciator. Potential
faults that cause the UAT status LED to turn on and the status discrete to be active (ground)
are listed in Table 4002.

Table 4002. UAT Status LED/Discrete Fault Indications

Problem Reported

Reported By

RF transmission failure

PBIT

Bottom antenna not connected (if DC ground check configured)

PBIT

Top antenna not connected (if DC ground check configured)

PBIT

EFFECTIVITY

ALL

Page 4001

22 Dec 2016

© Honeywell International Inc. Do not copy without express permission of Honeywell.

Содержание 89000016-130






















































































































































































Отзывы:

Нет отзывов