Baumuller BUS 6-T Series Скачать руководство пользователя страница 87

Страница: 87 / 119

Parameter set 0

Parameters

Controller BUS 6 T

Baumüller Nürnberg GmbH

5.94017.06

integral-action time adaptation

Below the lower adaptation limit the integral-action time adaptation indicates the percentage

value referring to the speed controller integral-action time (ID no. 101). Above the upper

adaptation limit the speed controller proportional gain changes linearly taking the adaptation

of the integral-action time and the current speed into account.

set velocity window KI counter N_I_component)

The KI counter is set at a preset difference between set speed value and actual speed

value.

If this parameter is set to 1000 rpm, the speed controller's integral-action component is not

deleted.

delete velocity window N_I_component

This parameter specifies the difference between set speed value and actual speed value at

which the KI counter is counted back and the speed controller's integral-action component

deleted.

actual speed value time constant

For smoothing the actual speed value a time constant can be set here.

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды