Baumuller BUS 6-T Series Скачать руководство пользователя страница 78

Страница: 78 / 119

Parameters

Display and measuring parameters

Controller BUS 6 T

5.94017.06

Baumüller Nürnberg GmbH

Parameter description

These parameters display internal values of the controller.

actual position value

The actual position value displayed refers to the ROD encoder in the motor. 0 corresponds

to the position of the reference signal after completion of the reference run.

hardware version

software version

These parameters display the hardware or software version of the controller used.

The software version contents 2 groups of figures

Example:

01 02

incompatible software version

compatible software version

Incompatible software version means, the new software isn´t able to read the data sets in

the EEprom. Before the software is changed, the data from the EEprom has to be stored on

disk or noted by hand.

An incompatible software e.g. originates from a new ID no. (additionally the file

PCBASS.CFG must be supplemented by this number, see manual operation software).

Compatible software version means, the software is enlarged with additional functions or is

changed for customer, without needing a new ID no.

error bar of I/O component boot

boot initialisation error

If an error occurs during the controller's boot procedure, this error bar is activated and

controller enabling is not possible (controller inhibit).

See chapter 7.2.1 Error messages.

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды