Baumuller BUS 6-T Series Скачать руководство пользователя страница 116

Страница: 116 / 119

Maintenance

Disposal

110

Controller BUS 6 T

5.94017.06

Baumüller Nürnberg GmbH

8.3 Disposal

The units consist essentially of the following components and materials

Components

Material

Housing, various intermediate plates, fan coil, support plates

Steel plate

Heat sinics in power unit

Aluminium

Various distance bolts

Steel

Various distance bolts, current converter hausing and fan
housing

Plastic

Power unit rails

Copper

Cable looms

PVC insulated calbe leads

Power electronics

Metal base plate: Semiconductor chip, plastic
housing, various insulation material.

Cunductor plates, accomodating the complete control and
regulation electronic

Base material: EPOXY resin (filled with GRP).
Copperplated on both sides and with
interconnected channels. Various electronic
components such as capacitors, resistors,
relays and semi-conductor components, etc.

The electronic components can, on account of technical demands, contain dangerous materials.

In normal use the various components da not represent a danger to humans or environment.

In the event of fire dangerous materials may be released

The electrical components should not be opened since, for the purpose of internal insulation, (e.g. on

various power semi-conductor) beryllium oxide has been used. The beryllium dust caused by opening

represents a health hazard.

The disposal of the units should conform to the recycling regulations of the country und region in

which they are disposed.

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды