Baumuller BUS 6-T Series Скачать руководство пользователя страница 74

Страница: 74 / 119

Parameters

Display and measuring parameters

Controller BUS 6 T

5.94017.06

Baumüller Nürnberg GmbH

amplifier warning temperature

If the amplifier temperature exceeds the amplifier warning temperature, the drive sets the

bit "amplifier warning temperature" in Class 2 Diagnostics (see ID no. 12).

NOTE

Exceeding the temperature does not cause pulse or controller inhibit.

amplifier shutdown temperature

If the amplifier temperature exceeds the amplifier shutdown temperature, the drive sets the

bit "amplifier shutdown temperature" in Class 1 Diagnostics (see ID no. 11).

NOTE

Exceeding the temperature causes controller inhibit.

motor warning temperature

If the motor temperature exceeds the motor warning temperature, the drive sets the bit

"excess motor temperature warning" in Class 2 Diagnostics (see ID no. 12). With DS motors

this function is not evaluated.

NOTE

Exceeding the temperature does not cause pulse or controller inhibit.

motor shutdown temperature

If the motor temperature exceeds the motor shutdown temperature, the drive sets the bit

"excess motor temperature shutdown" in Class 1 Diagnostics (see ID no. 11).

NOTE

Exceeding the temperature causes controller inhibit.

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды