Baumuller BUS 6-T Series Скачать руководство пользователя страница 36

Страница: 36 / 119

Installation

Connector pin assignment

Controller BUS 6 T

5.94017.06

Baumüller Nürnberg GmbH

Parameter set selection:

Input 3 (S2)

Input 4 (S1)

Parameter set

Low

High

Low

High

Reset:

Reset activ if +24 V edge

This input corresponds with its function the command reset error status class 1 (ID no. 99).

If this input is enabled, the output X3:25 (error status class 1) at the same time is high and the LED

„Error“ lights. The „ready for use“ LED goes out and the relay output X3:7/8 is opened (not ready

for use). This reset action lasts approximately 4 s.

The controller´s status is „error“ if it is switched on. When the internal check was successfully,

the ready for use signal is given.

If there is no error and the reset signal is given, the controller´s status changed to „error“ and

when the internal check was successfully the ready for use signal is given again.

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды