manualshive.com logo in svg

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Техническое описание и операционное руководство по продукту серии Baumuller BUS 6-T. Скачайте это бесплатное руководство с нашего сайта, чтобы узнать подробности о функционале и эксплуатации этого продукта. Посетите manualshive.com, чтобы скачать руководство в формате PDF.

Поделиться
Скачать
background image

Table of contents

II

Controller BUS 6 T

5.94017.06

Baumüller Nürnberg GmbH

7 Parameters ......................................................................................................... 49

7.1 Function diagram ........................................................................................................ 49

7.2 Basic settings.............................................................................................................. 50

7.2.1 Basic settings (menu page 1 - 2).................................................................. 51
7.2.2 Motor-specific values (menu pages 3 - 5) .................................................... 57

7.3 Display and measuring parameters ............................................................................. 63

7.3.1 Display of nominal and peak values (menu page 6) ..................................... 63
7.3.2 Random-check generator  - square-wave generator  (menu page 7) ............ 64
7.3.3 Characteristic curve of magnetisation (asynchronous machines only) .......... 66
7.3.4 Temperature monitoring .............................................................................. 67
7.3.5 Measuring channel 1 and 2 .......................................................................... 69
7.3.6 Display of controller parameters .................................................................. 71

7.4 Parameter set 0 .......................................................................................................... 73

7.4.1 Velocity and ramp function generator........................................................... 74
7.4.2 Rounding generator and torque.................................................................... 77
7.4.3 Speed controller .......................................................................................... 79
7.4.4 Messages - monitoring................................................................................. 82

7.5 Parameter set 1 .......................................................................................................... 84

7.6 Parameter set 2 .......................................................................................................... 86

7.7 Parameter set 3 .......................................................................................................... 88

7.8 Encoder evaluation ..................................................................................................... 90

7.9 Set adaptation ............................................................................................................ 93

7.10 Position control  (asynchronous motors).................................................................... 94

7.10.1 Position control and reference run ............................................................. 94
7.10.2 Spindle positioning..................................................................................... 97

8 Maintenance....................................................................................................... 99

8.1 Maintenance notes...................................................................................................... 99

8.2 Status messages ........................................................................................................ 100

8.2.1 Error messages ........................................................................................... 101
8.2.2 Warnings and messages.............................................................................. 107

8.3 Disposal...................................................................................................................... 110

9 Appendix ............................................................................................................ 111

9.1 Manufacturer´s declaration ......................................................................................... 111

9.2 Index .......................................................................................................................... 112

Содержание BUS 6-T Series
























































































































Отзывы:

Нет отзывов

Похожие инструкции для BUS 6-T Series

ABB FPBA-01 PROFIBUS DP Quick Installation And Start-Up Manual preview
FPBA-01 PROFIBUS DP
Бренд: ABB Страницы: 2
ABB ControlMaster CM15 Instructions preview
ControlMaster CM15
Бренд: ABB Страницы: 4
Panasonic FP0 Series Specifications preview
FP0 Series
Бренд: Panasonic Страницы: 27
Panasonic CZ-64ESMC2 Instruction Manual preview
CZ-64ESMC2
Бренд: Panasonic Страницы: 78
Panasonic GM1 Series Reference Manual preview
GM1 Series
Бренд: Panasonic Страницы: 98
NAiS FP0 Series Hardware Manual preview
FP0 Series
Бренд: NAiS Страницы: 173
Panasonic SL-VGU1-EC Instruction Manual preview
SL-VGU1-EC
Бренд: Panasonic Страницы: 2
Baby Trend 7548 Instruction Manual preview
7548
Бренд: Baby Trend Страницы: 8
Baby Trend 7311 Instruction Manual preview
7311
Бренд: Baby Trend Страницы: 19
Baby Trend 1305 Instruction Manual preview
1305
Бренд: Baby Trend Страницы: 5
Baby Trend 1140RC Instruction Manual preview
1140RC
Бренд: Baby Trend Страницы: 4
Camozzi PRE Series Operation And Maintenance Instructions preview
PRE Series
Бренд: Camozzi Страницы: 33
Camozzi K8 Series Use And Maintenance Instructions preview
K8 Series
Бренд: Camozzi Страницы: 2
Camozzi PME Series Operation & Maintenance Instructions Manual preview
PME Series
Бренд: Camozzi Страницы: 64
K'Nex Education 79018 User Manual preview
79018
Бренд: K'Nex Education Страницы: 56
MAKOT UMS-02 Manual preview
UMS-02
Бренд: MAKOT Страницы: 6
FrSky R9M Instruction Manual preview
R9M
Бренд: FrSky Страницы: 2
NXP Semiconductors AN10815 Application Note preview
AN10815
Бренд: NXP Semiconductors Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды