Baumuller BUS 6-T Series Скачать руководство пользователя страница 23

Страница: 23 / 119

Hazard notes

Installation

Controller BUS 6 T

Baumüller Nürnberg GmbH

5.94017.06

5 I

NSTALLATION

5.1 Hazard notes

WARNING

This unit carries dangerous voltage and contains dangerous rotating machine parts (ventilators). This

means that death, serious injury or considerable material damage can occur if the safety and warning

notes are not heeded.

The user is responsible for the assembly of the converter power unit, the motor, the transformer and

the other components according to applicable safety standards (e.g. DIN, VDE) and all other relevant

national or local regulations regarding conductor dimensions and fusing, grounding, circuit breakers,

overcurrent protection etc.

Relatively high leakage to ground occurs in the converter and the motor, i.e. the drive may be

incompatible with residual current protective devices (corresponding to DIN VDE 0160, sect. 5.5.3.4

and sect. 6.5.2.1).

The intermediate circuit carries electrical potential: it is imperative that the provided cover is used.

Variable-speed drives may only be used if they conform to valid VDE regulations.

With equipment where speed is of critical importance, speed monitoring in the unit must be

supplemented by autarchic monitoring of the motor. This speed check, independent from the control,

can be carried out by inductive, optical or yield force-dependant encoders. See the operation and

maintenance manual for the applicable motor.

Setial care is needed when touching the drive shaft, directly or indirectly (by hand). This should only

be done in a voltage-free state and whilst the drive is stationary.

Safety equipment must under no circumstances be shut down.

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды