Baumuller BUS 6-T Series Скачать руководство пользователя страница 82

Страница: 82 / 119

Parameters

Parameter set 0

Controller BUS 6 T

5.94017.06

Baumüller Nürnberg GmbH

positive velocity limit value

The positive velocity limit value describes the maximum permissible velocity in positive

direction. If the limit value is exceeded, the message in Class 3 Diagnostics is displayed.

negative velocity limit value

The negative velocity limit value describes the maximum permissible velocity in negative

direction. If the limit value is exceeded, the message in Class 3 Diagnostics is displayed.

bipolar velocity limit value

The bipolar velocity limit value describes the maximum permissible velocity in both

directions. If the limit value is exceeded, the message in Class 3 Diagnostics is displayed.

actual velocity value

This parameter displays the current actual velocity value.

ramp function generator

This parameter activates the ramp (ramp-up time/ramp-down time) in the main spindle area.

ramp-up time

The acceleration of the machine can be set via the ramp-up time. The selected time refers

to a set value alteration of 100 %.

ramp-down time

The deceleration of the machine can be set via the ramp-down time. The selected time

refers to a set value alteration of 100 %.

NOTE

If the drive is slowed down by activation of the controller inhibit (X3:16 low), the set ramp-

down time does not apply. The drive slows down at the set torque limit.

If the halt command is activated (X3:17 high), the drive decelerates with the preselected

ramp-down time.

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды