Baumuller BUS 6-T Series Скачать руководство пользователя страница 69

Страница: 69 / 119

Display and measuring parameters

Parameters

Controller BUS 6 T

Baumüller Nürnberg GmbH

5.94017.06

7.3 Display and measuring parameters

7.3.1 Display of nominal and peak values (menu page 6)

Parameter overview

ID no.

Name

Range

min. ... max.

Unit

Standard

value

Display

only

menu page 6

display of nominal and peak values

111

nominal motor current

1.000 ... 500.000

109

peak motor current

1.000 ... 500.000

112

nominal amplifier current

1.000 ... 500.000

110

peak amplifier current

1.000 ... 500.000

32780

actual value of intermediate circuit
voltage

0 ... 700

Parameter description

nominal motor current

This parameter displays the nominal motor current. The displayed value must correspond to

the value on the motor's rating plate.

This parameter should be set on the same value as apparent set current value

(ID no. 32816) displayed.

peak motor current

This parameter is used as a memory for the maximum current of the motor.

This parameter should be set on the same value as apparent set current value

(ID no. 32817) displayed.

nominal amplifier current

This parameter serves to display the permanently permissible nominal current of the

converter for an ambient temperature of 35 °C.

peak amplifier current

Display of the temporarily permissible peak current of the converter. The amplifier's peak

current is limited by measures on the unit itself, thus determining the current for the

maximum attainable torque limit values.

actual value of intermediate circuit voltage

Display parameter for the intermediate circuit voltage.

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды