Baumuller BUS 6-T Series Скачать руководство пользователя страница 108

Страница: 108 / 119

Maintenance

Status messages

102

Controller BUS 6 T

5.94017.06

Baumüller Nürnberg GmbH

Manufacturer Class 1 Diagnostics

Display of drive interlocking. A Class 1 Diagnostics error situation detected by the drive

leads to:

•

controller inhibit with brake down or pulse inhibit

•

setting of error bit.

Bit no.

Meaning

1: operating error BUS (PI or CI)

1: hardware error BUS (PI)

1: software error BUS (PI)

3 ... 7

reserved

1: operating error BUG supply (PI)

1: hardware error BUG supply (PI)

10 ... 15

reserved

PI (pulse inhibit)

CI (controller inhibit)

Delete the error bit (after remedying the fault) with the reset command (ID no. 99). When

switching on again a reset signal is automatically generated.

command "reset Class 1 Diagnostics"

If the drive receives this command via the service channel, Class 1 Diagnostics,

Manufacturer Class 1 Diagnostics and drive interlocking are deleted provided no more

errors are present.

The current error messages are deleted via the command

and

If an error in the BUG supply is present, the error must be deleted by switching the entire

supply voltage off and then on again (wait for the intermediate circuit capacitors to

discharge).

Additionally this command can be activated with digital input X22:3 (+24 V necessary).

Bit no.

Meaning

0: delete command in drive
1: set command in drive

0: interrupt command execution
1: enable command execution

2 ... 15

reserved

Содержание BUS 6-T Series
























































































































Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды

Baumuller BUS 6-T Series, Техническое описание и руководство по эксплуатации

Результаты поиска

Содержание BUS 6-T Series

Отзывы:

Похожие инструкции для BUS 6-T Series

Бренды по названию

Популярные бренды