Avaya IP500 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 442

Avaya IP500 Скачать руководство пользователя страница 40

Installing IP500/IP500 V2

Page 40

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

1.10.2 Power Supply Cords

Each control unit and expansion module requires a switched power outlet socket rated at 110-240V ac, 50-60Hz.
Connection from that power outlet socket requires an appropriate locale specific power cord which is not supplied with the
unit and must be ordered separately. Note that if the power cord includes an earth lead, the power outlet must be
connected to a protective earth.

Power cords must not be attached to the building surface or run through walls, ceilings, floors and similar openings.
Installation measures must be taken to prevent physical damage to the power supply cord, including proper routing of the
power supply cord and provision of a socket outlet near the fixed equipment or positioning of the equipment near a socket
outlet.

For locales not detailed below an appropriate power cord must be obtained locally.

Power Cord Type

Power Outlet Plug Type

Locales

SAP Codes

Earthed Power Cords (IEC60320 C13)

Control Units

·

IP500 V2.

·

IP500.

IP400 External Expansion Modules

·

Digital Station V2.

·

Phone V2.

·

So8.*

IP500 External Expansion Modules

·

BRI So8.

·

Digital Station 16/30.

·

Phone 16/30.

CEE7/7 (Schuko)

Europe and
South Africa.

700289762

BS1363

Czech Republic,
Ireland, United
Kingdom.

700289747

NEMA5-15P / CS22.2
No.42

North, Central
and South
America.

700289770

Unearthed Power Cord (IEC60320 C7)

IP400 External Expansion Modules

·

Analog.

·

Digital Station V1.

·

Phone V1.

IP500 External Expansion Modules

·

Analog Trunk 16.

CEE7/16 (Europlug)

Europe and
South Africa.

700213382

BS1363

Czech Republic,
Ireland, United
Kingdom.

700213374

NEMA1-15

North, Central
and South
America.

700213390

Korea.

700254519

*Older units were supplied with a 40W unearthed PSU and required an IEC60320 C7 power cord.

«
...
38
39
40
41
42
...
»

Содержание IP500



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды