manualshive.com logo in svg

Avaya IP500, Руководство по установке

Поделиться
Скачать
Avaya IP500 Скачать руководство пользователя страница 392

Installing IP500/IP500 V2

Page 392

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

10.15.5 BRI Port (To)

These ports are BRI To interface ports for connection to external BRI trunk services. Note that BRI ports found on the
IP400 So8 module are BRI-S interface ports for connect to ISDN terminal devices, see 

BRI Port (So)

.

 

PRI/BRI Trunk Cable

This cable is used to connect from IP Office BRI/PRI trunk ports to the line providers network termination equipment. If
that equipment does not use RJ45 sockets, the cable may need to be stripped and rewired or an alternate cable used. The
appropriate signal pin-outs and wire colours are detailed below.

 

IP Office

Wire

Network
Termination

BRI

 RJ45

BRI

PRI

PIN

RJ45

1

–

Rx-A

White/Orange

1

2

–

Rx-B

Orange/White

2

3

Tx-A

–

White/Green

3

4

Rx-A

Tx-A

Blue/White

4

5

Rx-B

Tx-B

White/Blue

5

6

Tx-B

–

Green/White

6

7

–

–

White/Brown

7

8

–

–

Brown/White

8

·

Supply: BRI/PRI trunks cards are not supplied with these cables.

·

Cable Color: Red.

·

SAP Code: 700213440.

·

Standard Length: 3m/9'10".

·

Maximum Length: 5m/16'5''. 

·

Though not used pins 7 and 8 are through connected for ease of construction.

391

Содержание IP500



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды