manualshive.com logo in svg

Avaya IP500, Руководство по установке

Поделиться
Скачать
Avaya IP500 Скачать руководство пользователя страница 258

Installing IP500/IP500 V2

Page 258

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

10.7.1 Analog Trunk Card Uni (ATM4U)

This card supersedes the previous Analog Trunk cards and is referred to as the "ATM4U". It can be identified by a label on
the base of the card.

The card is supported on IP Office software 2.1(36) and higher. Unlike the previous ATM4 card, the same ATM4U card
variant can be used in all locales.

For systems running IP Office software 3.1 or higher, the echo cancellation used on each trunk can be switched off or on
(16ms).

The card provides 4 RJ45 sockets for 

analog trunk connections

. The card only supports loop-start trunks. For ground-

start trunks an 

Analog Trunk expansion module

 should be used.

·

Power Failure Operation 
There are no power failure extension connections provided for the analog trunk card. If this is a requirement, the
ATM16 expansion module should be used.

·

 WARNING 

In all IP Office installations, any module or control unit using analog trunk connections must be connected to a 

functional earth

.

·

 WARNING 

Within the Republic of South Africa and in areas of high lightning risk, any module or control unit using analog trunk
connections must be connected to a 

protective ground

 and to 

surge protection equipment

.

ATM4U Trunk Card

Country

SAP Code

IP500

IP500

V2

ATM4 Uni (Loop-Start)

All

700359938

·

The card includes two plastic stand off pillars for installation and a replacement blanking plate for the rear of IP400
control units.

·

For the IP500 and IP500 V2 control units, an IP500 Carrier Card is required, up to a maximum of 2 IP500 Carrier
Cards.

 

390

266

44

44

45

Содержание IP500



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды