Avaya IP500 Скачать руководство пользователя страница 387 | Manualshive

Страница: 387 / 442

Avaya IP500 Скачать руководство пользователя страница 387

Installing IP500/IP500 V2

Page 387

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

System Components: Applications

10.15 Physical Ports

The following port types are found on IP Office systems:

·

ANALOG

Used for the connection of external analog trunks.

·

AUDIO

Used for input of an external music on hold source.

·

BRI

Used for connection of BRI trunks (Quad BRI trunk card). In IP Office standard modes they can also be used for
ISDN terminals devices (So8 module).

·

DC I/P

Power input from external power supply unit.

·

DS

Connection of Avaya digital station phones supported by IP Office.

·

RS232/DTE
Used for control unit maintenance under Avaya guidance. On expansion modules not used.

·

EF

Emergency power failure ports found on the ETR6 base card.

·

ETR

Only supported on IP500 V2 control unit running in IP Office Basic Edition - PARTNER® Mode or IP Office Basic
Editions.

·

EXPANSION

Used for interconnection of external expansions modules and control units.

·

EXT O/P

Used to control external relay systems. The port provides two switchable (on, off and pulse) controls.

·

Used for connection of functional or protective ground if required.

·

LAN

10/100Mbps Ethernet LAN ports.

·

PF

Analog power fails ports.

·

PHONE

(POT)

Analog phone extension ports. On older units these ports are labeled as POT ports.

·

PRI

PRI trunk ports.

·

TCM (RJ21)

and

TCM (RJ45)

Connections for M-Series and T-Series phones supported by IP Office. Also for Digital Mobility Solution system
supporting 4100 Series and 7400 Series phones. See supported

Avaya TCM digital phones

.

·

USB
Not used.

390

390

392

393

393

394

394

395

173

396

397

398

398

399

401

401

48

«
...
385
386
387
388
389
...
»

Содержание IP500



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды