Avaya IP500 Скачать руководство пользователя страница 194 | Manualshive

Страница: 194 / 442

Avaya IP500 Скачать руководство пользователя страница 194

Installing IP500/IP500 V2

Page 194

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

9.4.3 IP500 Card Insertion

Having prepared each IP500 base card by adding any

trunk daughter card

or

IP400 legacy card

, the base card can

be inserted into the control unit.

·

Warnings

·

Correct anti-static protection steps should be taken while handling circuit boards.

·

Cards must never be added or removed from the control unit while it has power connected.

·

Tools Required

·

o

5mm Flat-blade screwdriver.

·

o

Anti-static wrist strap and ground point.

Installing an IP500 Card

1. Check that there is no power to the control unit.

2. Using a flat-bladed screwdriver, remove the cover from the slot on the front of the control unit that will be used for

each card being installed. This cover is no longer required but should be retained until installation has been
completed.

3. Allowing the card to rest against the bottom of the slot, begin sliding it into the control unit. When half inserted,

check that the card rails have engaged with the slot edges by trying to gently rotate it. If the card rotates remove it
and begin inserting it again.

4. The card should slide in freely until almost fully inserted. At this point apply pressure at the base of the front of the

card to complete insertion.

5. Using a flat-bladed screwdriver secure the card.

6. Reapply power to the control unit. Initially each card should show a red LED (two if a daughter card is fitted) as the

control unit restarts. After approximately 30 seconds these should change to flashing red as the card is started.
These should then change to flashing every 5 seconds if the cards have started correctly.

7. Run the System Status Application and verify that the cards have all been recognized.

8. IP Office Manager can now be used to configure the extensions and trunk lines. For any IP500 VCM base cards, VCM

Channel licenses must be added to the configuration to enable channels above the base 4.

191

193

«
...
192
193
194
195
196
...
»

Содержание IP500



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды