Avaya IP500 Скачать руководство пользователя страница 195 | Manualshive

Страница: 195 / 442

Avaya IP500 Скачать руководство пользователя страница 195

Installing IP500/IP500 V2

Page 195

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

IP500 Basic Installation: IP500 Card Installation

9.5 Inserting the Feature Key

The IP500 uses a smart card feature key dongle. In addition to feature licensing the IP500
control unit uses this feature key dongle to determine various systems defaults such as A-Law or
Mu-Law operation, default short codes and trunk settings.

Warnings

1. The feature key is required for all IP500 control units and must be present when the system is

started and during operation. This applies even if the IP500 is not using any licensed features.

2. The feature key slot cover must remain present to protect the card and the card reader from

damage.

3. Correct anti-static protection steps should be taken before handling circuit boards.

4. During this process power to the IP Office control unit must be switched off and disconnected.

Parts Required

·

IP500 Feature Key
The correct key will depend on the locale. The listing below is typical and may not apply in all cases. Ensure that
the serial number of the key, shown on the card, is recorded.

·

o

Mu-Law: Used in North America and Korea.

·

o

A-Law: Used in all other locales.

Tools Required:

·

o

5mm Flat-blade screwdriver.

Procedure

1. Locate the feature key slot on the rear of the IP500 control unit. The slot is adjacent to the power input socket and

is protected by a metal cover.

2. Undo the screws on the cover until it can be rotated clear of the feature key card slot.

3. Insert the feature key. The card should be face up and inserted in the direction of the arrow on the card.

4. Rotate the slot cover back into position and tighten the screws.

«
...
193
194
195
196
197
...
»

Содержание IP500



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды