manualshive.com logo in svg

Avaya IP500, Руководство по установке

Поделиться
Скачать
Avaya IP500 Скачать руководство пользователя страница 190

Installing IP500/IP500 V2

Page 190

15-601042 Issue 28c (19 August 2013)

IP Office 9.0

9.3 IP500 Unpacking

Use the following procedure when unpacking any equipment supplied by
Avaya or an Avaya reseller or distributor. 

Information Required

·

o

 Equipment Checklist. 

An installation checklist of the parts and equipment ordered for the
installation.

Procedure

1.

o

 Check for Packaging Damage 

Before unpacking any equipment, check for any signs of damage that may have occurred during transit. If any
damage exists bring it to the attention of the carrier.

2.

o

 Check the Correct Parts Have Been Delivered 

Check all cartons against the packing slip and ensure that you have the correct items. Report any errors or
omissions to the equipment supplier.

3.

o

 Retain All Packaging and Documentation 

While unpacking the equipment, retain all the packaging material. Fault returns are accepted only if repackaged in
the original packaging. If performing a staged installation, the original packaging will also assist when repacking
equipment to be moved to the final install site.

4.

o

 Ensure that Anti-Static Protection Measures are Observed 

Ensure that anti-static protection measures are observed at all times when handling equipment with exposed
electrical circuit boards.

5.

o

 Check All Parts 

Visually inspect each item and check that all the necessary documentation and accessory items have been included.
Report any errors or omissions to the dealer who supplied the equipment.

6.

o

 Check All Documentation 

Ensure that you read and retain any documentation included with the equipment.

Содержание IP500



























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды