Analog Devices ADuCM355 Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 312

background image

Hardware Reference Manual

UG-1262

Rev. B | Page 71 of 312

Bits Bit

Name Settings

Description

Reset

Access

[11:8] SINC2OSR

Sinc2

Filter Oversampling Rates.

0x3

R/W

0

22 samples for this OSR setting.

1

44 samples for this OSR setting.

10

89 samples for this OSR setting.

11

178 samples for this OSR setting.

100

267 samples for this OSR setting.

101

533 samples for this OSR setting.

110

640 samples for this OSR setting.

111

667 samples for this OSR setting.

1000

800 samples for this OSR setting.

1001

889 samples for this OSR setting.

1010

1067 samples for this OSR setting.

1011

1333 samples for this OSR setting.

7

AVRGEN

Enable ADC Average Function.

0x0

R/W

0

Disable average.

1

Enable average. Average result feeds to next stage.

6

SINC3BYP

Sinc3 Filter Bypass.

0x0

R/W

0

Sinc3 filter active. Enable sinc3 filter.

1

Bypass sinc3 filter. Raw 800 kHz or 1.6 MHz ADC output data is fed directly to
gain offset adjustment stage. If the sinc3 filter is bypassed, the 200 kHz sine
wave can be handled directly by DFT block without amplitude attenuation. If
the sinc3 filter is bypassed and ADC raw data rate is 800 kHz, the gain offset
block output is used as DFT input.

5 Reserved

Reserved.

0x0

R

4

LPFBYPEN

50 Hz or 60 Hz Low-Pass Filter. Bypass both 50 Hz and 60 Hz notch filter.

0x0

R/W

1

Bypass both 50 Hz notch and 60 Hz notch filters.

0

Enable 50 Hz notch and 60 Hz notch filters. ADC result is written to the
SINC2DAT register.

[3:1] Reserved

Reserved.

0x0 R

0

ADCCLK

ADC Data Rate. Unfiltered ADC output rate.

0x1

R/W

1

800

kHz.

0

1.6 MHz. If ADC sample rate is 1.6 MHz, ADC clock frequency must be 32 MHz.

RAW RESULT REGISTER

Address: 0x400C2074, Reset: 0x00000000, Name: ADCDAT

This register is the ADC result register for raw ADC output or when sinc3 filter options are selected.

Table 65. Bit Descriptions for ADCDAT

Bits Bit

Name

Settings

Description

Reset

Access

[31:16] Reserved

Reserved.

0x0 R

[15:0] DATA

ADC Result. Register contains the ADC conversion result. Depending on user configuration,
result can reflect raw or sinc3 filter outputs. The result is a 16-bit unsigned number.

0x0 R/W

DFT RESULT, REAL PART REGISTER

Address: 0x400C2078, Reset: 0x00000000, Name: DFTREAL

Table 66. Bit Descriptions for DFTREAL

Bits Bit

Name

Settings

Description

Reset

Access

[31:18] Reserved

Reserved.

0x0 R

[17:0] DATA

DFT Real. DFT hardware accelerator returns a complex number. This register returns
the 18-bit real part of the complex number from the DFT result. The DFT result is
represented in twos complement.

0x0 R/W

«
...
69
70
71
72
73
...
»

Содержание ADuCM355

























































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ADuCM355

Бренд: QCON Страницы: 4

Бренд: Vageo Страницы: 2

Бренд: Vacon Страницы: 6

Бренд: Vacon Страницы: 24

Бренд: Vacon Страницы: 30

Бренд: Vacon Страницы: 81

Бренд: Vacon Страницы: 100

Бренд: EasyIO Страницы: 17

Бренд: RADEMACHER Страницы: 68

Бренд: Eaton Страницы: 448

Бренд: Wesa Страницы: 8

Бренд: Allen-Bradley Страницы: 162

Driver LED 1x2A/48V

Бренд: PXM Страницы: 11

Бренд: S&S Northern Страницы: 16

Lunar Shot Trem

Бренд: FuzzDog Страницы: 7

Бренд: H3C Страницы: 32

Бренд: DekoLight Страницы: 48

ENFORCER SLI PR-B1124-PQ

Бренд: SECO-LARM Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды