manualshive.com logo in svg

Analog Devices ADuCM355, Справочник по аппаратуре

Поделиться
Скачать
Analog Devices ADuCM355 Скачать руководство пользователя страница 299

ADuCM355

 Hardware Reference Manual 

UG-1262

 

Rev. B | Page 299 of 312 

Bits Bit 

Name 

Settings 

Description 

Reset 

Access 

  

0 

The WUT real-time count in CNT1, CNT0, and CNT2 has not risen due to a roll 
over. 

 

 

  

1 

The WUT real-time count currently in CNT1, CNT0, and CNT2 has rolled over 
from a value at or within trimming distance of its maximum to a value at or 
within trimming distance of its minimum. 

 

 

4 CNTMOD60ROLLINT 

 

WUT Modulo 60 Count Roll Over Interrupt Source. This bit sticks active high 
when the modulo 60 equivalent of the CNT1 and CNT0 count value rolls over 
from 59 to zero. Such a roll over event happens every 60 prescaled 
increments of the WUT count, or fewer if positive trimming is active. 

0x0 R/W1C 

  

0 

The modulo 60 value of CNT1 and CNT0 in CNTMOD60 has not rolled over 
since this bit was last cleared. 

 

 

  

1 

The modulo 60 value of CNT1 and CNT0 in CNTMOD60 has rolled over since 
this bit was last cleared. 

 

 

3 CNTROLLINT 

 

WUT Count Roll Over Interrupt Source. This bit sticks active high when the 
CNT1 and CNT0 count value rolls over from 2

32

 − 1 to zero or is trimmed such 

that the trim increment causes the WUT to pass through (potentially 
spanning) these maximum and minimum values. 

0x0 R/W1C 

 

 

0 

CNT1 and CNT0 have not rolled over since this bit was last cleared. 

 

 

 

 

1 

CNT1 and CNT0 have rolled over since this bit was last cleared. 

 

 

2 Reserved 

 

Reserved. 

0x0 

R/W1C 

1 PSINT 

 

WUT Prescaled Modulo 1 Boundary Interrupt Source. This bit sticks active 
high whenever the gated clock that defines the prescaled WUT time unit and 
the advancement of the WUT count is activated. For PSINT to cause an 
interrupt from the RTC, the corresponding enable bit for the interrupt fan in 
the PSINTEN bit in CR1 must be active high. This interrupt source is cleared 
by writing 1. Full interrupt capability is available for RTC1. 

0x0 R/W1C 

  

0 

The prescaled gated clock for the WUT count in CNT1, CNT0, and CNT2 has 
not activated since this bit was last cleared. 

 

 

  

1 

The prescaled gated clock for the WUT count in CNT1, CNT0, and CNT2 has 
activated since this bit was last cleared. 

 

 

0 CNTINT 

 

WUT Count Interrupt Source. CNTINT sticks active high whenever the value 
of CNT1 or CN0 changes. Such an event is not the same as the occurrence of 
a prescaled WUT time unit (as denoted by PSINT), because the WUT count 
can either be redefined or trimmed, which may or may not lead to value 
changes. This interrupt source is cleared by writing one to its bit position in SR2. 

0x0 R/W1C 

 

 

0 

The value of CNT1 and CNT0 has not changed since this bit was last cleared. 

 

 

 

 

1 

The value of CNT1 and CNT0 has changed since this bit was last cleared. 

 

 

 

SNAPSHOT 0 REGISTER 

Address: 0x40001430, Reset: 0x0000, Name: SNAP0

 

SNAP0 is a sticky snapshot of the value of CNT0. It is updated at the same time as its counterparts, SNAP1 and SNAP2, thereby 
overwriting any previous values of SNAP1, SNAP0, and SNAP2. This updating and overwriting occurs when the CPU writes a snapshot 
request key of 0x7627 to GWY.  

Table 390. Bit Descriptions for SNAP0 

Bits Bit 

Name 

Settings 

Description 

Reset Access 

[15:0] VALUE 

 Contains a Sticky Snapshot of CNT0. This channel takes a sticky snapshot of the 47-bit 

WUT count in CNT1, CNT0, and CNT2 and stores it in SNAP1, SNAP0, and SNAP2, 
respectively.  

0x0 R 

 

 

Содержание ADuCM355

























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды