manualshive.com logo in svg

Analog Devices ADuCM355, Справочник по аппаратуре

Поделиться
Скачать
Analog Devices ADuCM355 Скачать руководство пользователя страница 203

ADuCM355

 Hardware Reference Manual 

UG-1262

 

Rev. B | Page 203 of 312 

IRQ ABORT ENABLE (LOWER BITS) REGISTER 

Address: 0x4001803C, Reset: 0x00000000, Name: ABORT_EN_LO

 

Table 237. Bit Descriptions for ABORT_EN_LO 

Bits  Bit 

Name 

Settings Description 

Reset Access 

[31:0] VALUE[31:0] 

 System IRQ Abort Enable. To allow a system interrupt to abort an ongoing flash 

command, write 1 to the bit in this register corresponding with the desired system IRQ 
number. 

0x0 R/W 

 

IRQ ABORT ENABLE (UPPER BITS) REGISTER 

Address: 0x40018040, Reset: 0x00000000, Name: ABORT_EN_HI

 

Table 238. Bit Descriptions for ABORT_EN_HI 

Bits  Bit 

Name 

Settings Description 

Reset Access 

[31:0] VALUE[63:32] 

 System IRQ Abort Enable. To allow a system interrupt to abort an ongoing flash command,

write 1 to the bit in this register corresponding with the desired system IRQ number. 

0x0 R/W 

 

ECC CONFIGURATION REGISTER 

Address: 0x40018044, Reset: 0x00000002, Name: ECC_CFG

 

Table 239. Bit Descriptions for ECC_CFG 

Bits Bit 

Name  Settings 

Description 

Reset 

Access 

[31:8] PTR 

 ECC Start Page Pointer. Write Bits[31:8] of the start page address into Bits[31:8] of this 

register. This bit is a byte address for any page in user flash. The bottom bits of this 
address are ignored by the flash controller, forming a page address. When ECC is enabled 
and user code reads any address from within the page specified, ECC functions are 
performed. Reads from less significant pages bypass ECC entirely.  

0x0 R/W 

[7:2] Reserved 

 

Reserved. 

0x0 R 

1 INFOEN 

 

Information Space ECC Enable Bit. ECC is enabled by default for information space. 
Clearing this bit disables ECC in information space. This bit is not key protected. 

0x1 R/W 

0 EN 

 

ECC Enable. Set this bit to enable ECC on user space. ECC is enabled on all future 
flash reads in user space from any address between ECC_CFG, Bits[31:8] through the 
top of user space (inclusive). When cleared (or accessing addresses outside the 
enabled range), the flash controller returns the raw data in response to both ICode 
and DCode reads of user space. No error corrections are made or reported. 

0x0 R/W 

 

ECC STATUS (ADDRESS) REGISTER 

Address: 0x40018048, Reset: 0x00000000, Name: ECC_ADDR

 

This register is updated when ECC error or correction events occur. ECC error and correction events can generate interrupts if the 
appropriate bits of the IEN register are selected, which generates a bus fault. This register records the address of the first ECC error or 
correction event to generate an interrupt since reset or the last time the ECC status bits were cleared. If the status bits are cleared in the 
same cycle as a new ECC event (selected to generate an IRQ), a new address is recorded and the status bits remain set. 

Errors have priority over corrections. Two or more corrupt bits results in an error. A correction results in proper data being returned 
after a single bit is corrected. If an error and a correction occur in the same cycle, this register reports the error address. When two of the 
same priority ECC events occur (both errors or both corrections), the ICode bus has priority over DCode. As such, if both ICode and 
DCode buses generate the same type of ECC event in the same cycle, the ICode address is stored in this register. 

The register cannot be cleared except by reset. It always holds the address of the most recently reported ECC correction or error. 

Table 240. Bit Descriptions for ECC_ADDR 

Bits Bit 

Name  Settings 

Description 

Reset 

Access 

[31:19] Reserved 

 

Reserved. 

0x0  R 

[18:0] 

VALUE 

 

Address for Which ECC Error Is Detected. 

0x0 

R 

 

Содержание ADuCM355

























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды