manualshive.com logo in svg

Amsco Century Series, Регулярное техническое обслуживание

Поделиться
Скачать
Amsco Century Series Скачать руководство пользователя страница 49

5-24

129367-410

Routine Maintenance

Troubleshooting

Alarm

Description

Screen with Service Instructions

Too Long To Seal Door,

Continued

STATUS..

SERVICE INFORMATION:

228

TOO LONG TO SEAL DOOR

→

DOOR SEAL DID NOT REACH 10 PSIG

WITHIN ALLOTTED TIME

CAUSES AND CORRECTION:

1.

SEAL PRESSURE SWITCH MALFUNCTION

→

READJUST PS1(PS2)

→

REPAIR PS1(PS2)

2.

SEAL NOT ACTIVATING

→

CHECK SEAL STEAM

→

CHECK SEAL EXHAUST

3.

SOLENOID VALVE MALFUNCTION

→

REPAIR S35(S36)

ABORT

CLEAR

PAPER

EXIT

ALARM

FEED

For Healthcare
Only

Occurs if door seal
pressure does not
drop below 10 psig
within allotted time.

Too Long To Unseal

Door

STATUS

PAPER

PRINT

FEED

SILENCE

SERVICE

ALARM

HELP

STATUS..

ALARM!

229

TOO LONG TO UNSEAL DOOR

CHAMBER:

000.0 C

00.0 psig

STERILIZER WILL:

•

REMAIN IN ALARM CONDITION UNTIL

DOOR IS UNSEALED

OPERATOR INSTRUCTIONS:

1. SILENCE ALARM

2. CALL SERVICE

3. IF LOAD MUST BE REMOVED, REFER TO

EMERGENCY DOOR OPERATION PROCEDURE

IN OPERATING MANUAL.

STATUS..

SERVICE INFORMATION:

230

TOO LONG TO UNSEAL DOOR

→

DOOR SEAL PRESSURE NOT BELOW 10 PSIG

WITHIN ALLOTTED TIME

CAUSES AND CORRECTION:

1.

SEAL PRESSURE SWITCH MALFUNCTION

→

READJUST PS1(PS2)

→

REPAIR PS1(PS2)

2.

SEAL NOT RETRACTING

→

CHECK SEAL STEAM

→

CHECK SEAL EXHAUST

3.

SOLENOID VALVE MALFUNCTION

→

REPAIR S37(S38)

→

REPAIR S35(S36)

PAPER

SERVICE

EXIT

FEED

MODE

For Life Sciences
Only

Screen with Operator Instructions

Screen with Service Instructions

Содержание Century Series



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды