manualshive.com logo in svg

Amsco Century Series, Регулярное техническое обслуживание

Поделиться
Скачать
Amsco Century Series Скачать руководство пользователя страница 27

5-2

129367-410

Routine Maintenance

Troubleshooting

SILENCE                    

ABORT

SERVICE

ALARM

HELP

For Healthcare
Only

CHAMBER:

000.0 C

00.0 psig

STERILIZER WILL:

•

AUTOMATICALLY TRY TO COMPLETE CYCLE

OPERATOR INSTRUCTIONS:

1. SILENCE ALARM

2. CHECK STEAM SUPPLY VALVE

→

IF CLOSED, OPEN VALVE

3. IF ALARM RECURS, CALL SERVICE

STATUS..

ALARM!

205

TOO LONG IN CHARGE

Figure 5-1.  Typical Alarm Screen

Current Chamber Status

Alarm Name

Operator Instructions

Screen

Reference

Number

Sterilizer Activity

STATUS

PAPER

PRINT

FEED

5.1.2  Typical Alarm

Printout

* ALARM
PRESSURE IN CHAMBER

F 10:07:23A

61.7C

34.OP

Full Print Format Shown

Figure 5-2.  Typical Alarm

Printout

Touch screen buttons, located along bottom of alarm screen, are used to
perform the following functions.

•

Pressing

 SILENCE ALARM

 turns off the alarm buzzer.

•

Pressing 

STATUS PRINT

 generates a printout of the current temperature

and pressure in the sterilizer chamber at the time the button was pressed.

•

Pressing 

PAPER FEED

 advances the printer paper up by one line.

•

Pressing 

SERVICE HELP

 advances display to the corresponding service

information screen.  This screen provides the qualified service technician
with possible causes and advanced corrective actions for that alarm
condition.

IMPORTANT:  In the event of an alarm condition, the operator should always
follow the instructions indicated on the alarm screen.

When an alarm occurs the printer automatically generates a printout, typically
listing alarm name, time alarm occurred, current chamber status and any
associated sensor temperature. See Figure 5-2.

The following alarm screens will appear only during cycle operation.

5.2 In-Cycle Alarms

Alarm

Description

Screen with Operator Instructions

Occurs if chamber does
not reach the set tem-
perature within the
allotted time.

Too Long In Charge

STATUS

PAPER

PRINT

FEED

SILENCE

SERVICE

ALARM

HELP

CHAMBER:

000.0 C

00.0 psig

STERILIZER WILL:

•

AUTOMATICALLY TRY TO COMPLETE CYCLE

OPERATOR INSTRUCTIONS:

1. SILENCE ALARM

2. CHECK STEAM SUPPLY VALVE

→

IF CLOSED, OPEN VALVE

3. IF ALARM RECURS, CALL SERVICE

STATUS..

ALARM!

205

TOO LONG IN CHARGE

For Life Sciences
Only

Содержание Century Series



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды