manualshive.com logo in svg

Amsco Century Series, Регулярное техническое обслуживание

Поделиться
Скачать
Amsco Century Series Скачать руководство пользователя страница 46

5-21

Troubleshooting

Routine Maintenance

129367-410

The following alarm screens will appear any time the sterilizer is energized.
The sensors are continually monitored whenever the sterilizer is in or out of
cycle.

5.4 Sensor Alarms

Alarm

Description

Screen with Operator Instructions

Water In Chamber

Occurs if excess water
is sensed in the
chamber.

STATUS

PAPER

PRINT

FEED

SILENCE

SERVICE

ALARM

HELP

CHAMBER:

000.0 C

00.0 psig

WARNING - BURN HAZARD!

CHAMBER MAY BE FILLED WITH STEAM

CONDENSATE

OPERATOR INSTRUCTIONS:

1. DO NOT OPEN DOOR

2. SILENCE ALARM

3. CALL SERVICE IMMEDIATELY

STATUS..

ALARM!

209

WATER IN CHAMBER

Screen with Service Instructions

STATUS..

SERVICE INFORMATION:

210

WATER IN CHAMBER

→

EXCESS WATER SENSED IN CHAMBER,

WARNING! BURN HAZARD

CAUSES AND CORRECTION:

1.

JACKET STRAINER PLUGGED

→

CLEAN

2.

JACKET TRAP FAILED CLOSED

→

REPAIR

3.

CHAMBER TRAP FAILED CLOSED

→

REPAIR

4.

WATER ENTERED CHAMBER THROUGH STEAM

PIPING

→

CHECK BOILER OR STEAM GENERATOR

→

REPAIR PIPING

5.

WATER FLOAT SENSOR MALFUNCTION

→

REPAIR

PAPER

SERVICE

EXIT

FEED

MODE

For Life Sciences
Only

STATUS..

SERVICE INFORMATION:

210

WATER IN CHAMBER

→

EXCESS WATER SENSED IN CHAMBER,

WARNING! BURN HAZARD

CAUSES AND CORRECTION:

1.

JACKET STRAINER PLUGGED

→

CLEAN

2.

JACKET TRAP FAILED CLOSED

→

REPAIR

3.

CHAMBER TRAP FAILED CLOSED

→

REPAIR

4.

WATER ENTERED CHAMBER THROUGH STEAM

PIPING

→

CHECK BOILER OR STEAM GENERATOR

→

REPAIR PIPING

5.

WATER FLOAT SENSOR MALFUNCTION

→

REPAIR

PAPER

EXIT

FEED

For Healthcare
Only

Содержание Century Series



























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды