AcraDyne Gen IV Скачать руководство пользователя страница 62

Страница: 62 / 125

Page

125

4.5.9 Master Spindle Setup

Several Gen IV controllers can be linked together via an Ethernet connection to create a multi-

spindle network. Operations requiring multiple fasteners to be inserted simultaneously or in a

synchronized fashion is possible with this setup. Up to 10 tools can be operated from one master

controller. The spindle network can be controlled via physical IO or across supported protocols.

PSets will be synchronized across the spindle network so PSets and Jobs will only need to be set

up on the master controller. Spindle rundown results are also viewable from the master.

Master Enabled: Enable or disable the spindle network.

Stop on Error:

All spindles will stop if any problem is reported

(bad rundown, a stop condition, or a cable disconnection has

occurred on any spindle). If this option is not checked,

spindles will finish the current rundown even if an error has

occurred on one spindle.

Trigger Source:

Select whether the start input for running the

spindle network comes from the master spindle’s tool trigger or

the start input from IO.

*All spindles need to have their start input set to respond to the

master tool in order to have them all run from a single trigger or

IO start signal. This is configured under Controller



Tool

Setup



Start Input and set the input source to ‘Start from

Master Tool’.

Latching Options:

Select latching throttle option. If Latch on

Time is selected, the spindle network will continue to run after

the throttle has been held down for the selected amount of

time.

4.5.9 Setting up Multi-Spindle Network

Hardware

Connect the master controller and slave spindles together via an Ethernet switch. Ensure that all

controllers have the appropriate tools connected and apply power.

Содержание Gen IV






























































































































Результаты поиска

Содержание Gen IV

Отзывы:

Похожие инструкции для Gen IV

Бренды по названию

Популярные бренды

AcraDyne Gen IV, Руководство оператора

Результаты поиска

Содержание Gen IV

Отзывы:

Похожие инструкции для Gen IV

Бренды по названию

Популярные бренды