Ace ACE-3205 Скачать руководство пользователя страница 27

Страница: 27 / 418

Installation and Operation Manual

Table of Contents

ACE-3105, ACE-3205 Ver. 5.2

Corrective Measures ..............................................................................................

6.4

Testing the Unit .......................................................................................................

6-73

Displaying Self-Test Results ..................................................................................

6-74

Performing Physical Loopback Tests ......................................................................

6-75

Performing Application Tests .................................................................................

6-77

Performing ATM Cell Tests ................................................................................

6-78

Performing IP Connectivity Tests .......................................................................

6-79

6.5

Troubleshooting .......................................................................................................

6-81

6.6

Recovering ACE Units ...............................................................................................

6-83

ACR Failure ...........................................................................................................

6-83

Determining the Condition of the Clock Recovery PW ........................................

6-83

Determining the Condition of the Clock Recovery PW on the Distribution Unit ...

6-85

Physical Link Failures .............................................................................................

6-86

PW Logical Failure .................................................................................................

6-87

Determining Physical Layer Faults .....................................................................

6-87

Logical Layer Faults ..........................................................................................

6-88

Device Disconnected .............................................................................................

6-92

Management Path Disconnections ....................................................................

6-93

Incorrect Access Parameters .............................................................................

6-93

Failure of the Management Plane in the ACE Unit..............................................

6-94

Loss of ATM Cells ..................................................................................................

6-94

Physical Line Errors ..........................................................................................

6-94

Policing/Shaping Issues .....................................................................................

6-95

Rx Congestions ................................................................................................

6-95

Packet loss/Misorder ........................................................................................

6-96

Packet Loss/Packets Mis-order ..............................................................................

6-96

Packet Mis-ordering .........................................................................................

6-96

Power Supply and Fan Failure ................................................................................

6-99

Changing the Fan Tray ......................................................................................

6-99

Changing the Power Supply Module ................................................................

6-100

Connecting to AC Power .................................................................................

6-100

Redundant Main Modules (MC) ............................................................................

6-100

Configuration Database ..................................................................................

6-101

MC redundancy is configured to ON ................................................................

6-102

Card Absent A/B .............................................................................................

6-102

Communication loss .......................................................................................

6-102

Underruns – TDM Pseudowire .............................................................................

6-103

6-105

Rx Congestions ...................................................................................................

6-106

ATM Bandwidth issues ....................................................................................

6-106

IMA ................................................................................................................

6-106

STM-1/CO-3 (155) ..........................................................................................

6-107

Insufficient PSN

ATM buffer size ...................................................................

6-107

Shaping Problems ...........................................................................................

6-107

Bursty Traffic Coming from the Remote Device ...............................................

6-108

IMA Failure ..........................................................................................................

6-108

Physical Failure ...............................................................................................

6-108

Minimal number of active links .......................................................................

6-109

Differential delay ...........................................................................................

6-109

Clocking issues ...............................................................................................

6-109

IMA Protocol Issues ........................................................................................

6-110

6.7

Frequently Asked Questions ...................................................................................

6-111

6.8

Technical Support ..................................................................................................

6-113

Содержание ACE-3205



































































































































































































































































































































































































































Результаты поиска

Содержание ACE-3205

Отзывы:

Ace ACE-3205, Инструкция по установке и эксплуатации, Страница: 27 / 418

Результаты поиска

Содержание ACE-3205

Отзывы: