Zerio-Plus EDA-Z5008 Installation & Operation Manual Download Page 4

Page: 4 / 48

EDA-Z5008, Z5020 & Z5100 – Technical Manual

ZPControlTechMan_r105

_____________________________________________________________________________________________________

Revision History

V0.10

27/08/2013

First draft release technical manual.

V0.11

01/10/2013

Draft release to test house.

V0.12

04/10/2013

Added access level descriptions.

V0.13

07/10/2013

Updated PCB layout.

V0.14

14/10/2013

Filename change, DOP updated.

V0.15

17/10/2013

EN54 approved functions added. Formatting changes.

V1.00

21/10/2013

First release.

V1.01

04/12/2013

Updated relay and delay information.

V1.02

14/01/2014

Updated text for type approval.

V1.03

11/02/2014

Updated control and indicating equipment options.

V1.04

06/03/2014

More information about panel relay settings and auto resound.

V1.05

29/04/2014

Added relay jumper positions and updated panel network.

Summary of Contents for EDA-Z5008

















































Search results

Summary of Contents for EDA-Z5008

Reviews:

Related manuals for EDA-Z5008

Brands by name

Popular brands

Zerio-Plus EDA-Z5008, Installation & Operation Manual

Search results

Summary of Contents for EDA-Z5008

Reviews:

Related manuals for EDA-Z5008

Brands by name

Popular brands