background image

EDA-Z5008, Z5020 & Z5100 – Technical Manual  

 

 ZPControlTechMan_r105 

_____________________________________________________________________________________________________ 

 

30 

 

6.29 - Adding a Device – commissioning users 

1.Main Menu>>1.Setup>>5.Device Setup>>2.Add Device

 

Additional  devices  can  be  added  to  the  system  at  any  time.  The  device  needs  to  be  put  into 
programming mode in order to add it to the system. First remove the device from its base or backplate.  
 

1.

 

If  a  smoke,  heat  detector  or  combined  sounder  is  being  programmed;  hold  both  the  reset 
button and the unit removal button down while you place the jumper link to the ON position.  

2.

 

If a beacon, sounder, callpoint, transmitter or I/O unit is being programmed; hold down the unit 
removal button while holding a magnet over the reed switch and move the jumper link to the 
ON  position.  Some  newer  devices  are  equipped  with  a  ‘log  on’  button  and  do  not  require  a 
magnet to program. Simply hold the button while placing the jumper link to the ON position. 

 
 
Continue to hold the button(s) for approximately 5 seconds until a 
confirmation of 3 beeps from the device is heard. The LED on the 
device  will  now  flash  green.  Press 

Enter

  to  scan  for  the  device. 

Once the device has been found, the device type will be displayed 
on  the  screen.  The  LED  on  the  device  will  stay  lit  until  the  device 
has been successfully added to the system. The device number and 
zone for the new unit should be selected using the cursor keys. You 
will  now  be  prompted  to  choose  from  using  either  the  device 
default  settings  set  by  the  control  panel  or  to  manually  set  the 
options.  All  options  are  entered  using  the  cursor  keys.  Once  you 
have chosen the options, press 

Enter

 to program. 

 
 
When adding a heat detector to the system, the user can select one of four operating modes: 
 

 

 

Fixed Point 

The device will go into alarm once the temperature reaches this point. The user  

 

 

 

can specify an alarm temperature from 50 – 99

o

C. 

 

Rate of Rise  The device will go into alarm when it senses a rapid increase in temperature. The 

 

 

 

user can choose from 3 levels of sensitivity.  

 

A1S

 

 

 

As specified by EN54 part 5, A1S detectors are intended for use in applications  

 

 

 

where the ambient temperature is typically around 25

o

C and not expected to  

 

 

 

exceed 50

o

C. A1S detectors will not respond below their minimum static    

 

 

 

response temperature of 54

o

C. A1S is the default setting. 

 

A1R 

 

As specified by EN54 part 5, an A1R detector is a rate of rise detector with a fixed 

 

 

 

upper limit of 57

o

C, at which the device will go into alarm if the rate of rise has  

 

 

 

been too slow to trigger the alarm earlier. 

 
 
 
 
 
 
 
 

 

  

 Device Programming 
 
 ENTER to continue 

    Device Scan 
      

 
    Please Wait 

    Device Found 
    HEAT/SOUNDER 
 

   A1S 

    Use ← → keys 

Summary of Contents for EDA-Z5008

















































Reviews: