background image

EDA-Z5008, Z5020 & Z5100 – Technical Manual  

 

 ZPControlTechMan_r105 

_____________________________________________________________________________________________________ 

 

36 

 

8.0 - Test Mode 

 

Test mode allows a system to be tested with minimal disruption to the occupants of a building. When a 
zone  is  placed  into  test  mode  the  engineer  can  choose  to  disable  sounders,  actuators  or  any  output 
devices.  Should  anything  happen  outside  of  these  selected  zones  the  system  will  operate  as  normal 
and the sounders will sound.   
 
Once the various Test Mode parameters have been chosen, the Test Mode LED will illuminate on the 
main panel. Once selected, the option is also given to save the parameters so that they can be used for 
subsequent  test  mode  operations.  When  a  zone  has  been  put  into  the  Test  condition,  subsequent 
alarms from devices in that zone do not appear on the Main Screen as an alarm, but appear as a “FIRE 
TEST” event in the event log. Refer to section 9.2 – View Event Log. 
 

8.1 - Test Zone – advanced, service and commissioning users

 

 

1.Main Menu>>3.Test Mode>>1.Test Zone 

Scroll to the appropriate zone number using the 

 or 

 keys, and 

press the 

 key to select that zone. Follow the on screen prompts 

to set the test parameters. 
 
Sounders: 

If sounders within the zone are to be disabled, select 

‘NO SOUND’

. Alternatively the sounders can be set to 

‘6  SEC  SOUND’

,  where  any  activated  sounders  will 

automatically silence after 6 seconds. This allows the 
engineer  to  perform  a  one-man  walk  test,  without 
the need to return to panel to silence the alarm. 

 
Timeout: 

This  is  the  amount  of  time  before  the  system  will 
automatically  exit  test  mode  operation.  A  timeout 
period of ‘0’ means that the zone will remain in test 
indefinitely,  until  the  test  is  disabled  by  the  user.  In 
order  to  operate  this  panel  and  comply  with  EN54 
part  2,  this  setting  should  not  be  set  to  anything 
other than ‘0’. It can be set in 1 hour intervals and is 
selected using the cursor keys. 

 
 
Once completed, press 

Enter

 to place the zone into test mode with the chosen settings. ‘Zone XXX in 

Test’ will be displayed on screen and the ‘Test Mode’ LED will illuminate. Multiple zones can be tested 
at the same time, by selecting ‘Enter more Zones’. The zone tests will be visible in the 

‘5-Tests’

 section 

of the quick menu.  
 

8.2 - Clear Zone in Test – advanced, service and commissioning users

 

 

1.Main Menu>>3.Test Mode>>2.Clear Zone in Test 

This option allows the user to cancel test mode for a zone currently 
in test. Select the zone and press 

Enter

. If no zones are in test the 

display  should  show  the  screen  opposite  and  the  ‘Test  Mode’  LED 
will extinguish. Press 

Cancel

 to return to the menu. 

 
      Zone 001↕ 
 
 

Use ← → keys 

 

Select Tone 

 

 NO SOUND↕ 

 
 

Use ← → keys 

 
  Timeout (hrs) 001↕ 
 
 

Use ← → keys 

 
  No Zones in Test 
 
   CANCEL to exit 

   

 Zone 001  

 

 in Test 

 
  ENTER to continue 

Summary of Contents for EDA-Z5008

















































Reviews: