Zaxcom Fusion 10 User Manual Download Page 163

Page: 163 / 168

Zaxcom Fusion User’s Manual_____________________________________________________Chapter 11

163

Know Firmware Issues

NOTE:

Turn „OFF‟ all effects before switching to a higher sampling-rate. If you want to use 192 kHz mode, then

you should perform a factory restore defaults to insure all effects are turned „OFF‟.

When changing from 192 kHz to 48 kHz sample-rate, select 96 kHz first as an intermediate step to prevent a

possible freeze. Holding the

key

while booting will force the Fusion back into 48 kHz mode.

NOTE:

Mirror Disk Playback must not be enabled while mirror mode is on. Doing so will cause the unit to

appear to be in playback when it is not. The

Play

key

may not update properly until the current page is

exited.

NOTE:

Playback from a DVD-RAM disk or FireWire drive often will not be fast enough to sustain the Fusion‟s

playback buffer. This will often result in only partial playback of a file. Press the

STOP

key

periodically to

allow the playback buffer to fill back up.

WARNING:

If you install software versions lower than z3.55 onto a Fusion, the internal DVD drive and CF card

slot will not function. This may make it difficult to install a newer version.

NOTE:

As of V4.00, you must select the folder to mirror. Fusion will no longer assume that you want to mirror

the current RECORD folder. You may also change the RECORD folder without affecting the currently

mirroring folder.

Firmware History

===================================================================================================================

V7.09

2010-03-16

Ver #

Ver Date

Fixed problem with Mix-8 / Mix-12 fader movement slowing down recording process

Changed expanded output routing to allow routing copies of outputs (to reduce duplicated crosspoints)

===================================================================================================================
V7.08

2009-12-16

ZAXNET BETA VERSION

Ver #

Ver Date

Changed Moved ZaxNet button to the left to avoid changes during touch screen malfunction

===================================================================================================================

V7.05

UNKNOWN

Ver #

Ver Date

Fixed Aux Line input trim 1 – 4 which were not being updated after a power cycle

Changed Allow over-clocked (by 10%) DSP speed (320MHz) when the #2 key is held during boot-up

Fixed Battery screen index

Fixed Meter label entry screen tab bug

Changed Properly update limiter crosspoint display

Fixed decimal point entry in battery meter screen (use backspace key)

===================================================================================================================

V7.03

UNKNOWN

Ver #

Ver Date

Fixed Was not properly saving the trim mode on digital inputs.

===================================================================================================================

V6.08K

UNKNOWN

Ver #

Ver Date

Changed No longer send ZaxNet commands if the Timecode screen is being displayed (for non ZaxNet compatible slates).

===================================================================================================================

V6.08F

UNKNOWN

Ver #

Ver Date

Added Low battery warning on boot up (9.0 volts).

===================================================================================================================
V6.06C

UNKNOWN

Ver #

Ver Date

Added F6 (INPUT key on Fusion) boot key: causes a folder recovery operation.

NOTE:

the recovered folder info is NOT written to the drive unless a recording is made in that folder!

===================================================================================================================

V6.03U

2009-06-26

Ver #

Ver Date

Changed Better free space left on mirror disk indicator on Mirror Drive Status button

===================================================================================================================

V6.02U

2009-06-25

Ver #

Ver Date

Changed potential bug in GUI that could cause a crash

Added free space left on mirror disk indicator on Mirror Drive Status button (FAT32 disks only)

Summary of Contents for Fusion 10









































































































































































Search results

Summary of Contents for Fusion 10

Reviews:

Related manuals for Fusion 10

Brands by name

Popular brands

Zaxcom Fusion 10, User Manual

Search results

Summary of Contents for Fusion 10

Reviews:

Related manuals for Fusion 10

Brands by name

Popular brands