YOKOGAWA AQ1215A User Manual Download

Page: 67 / 282

2-29

IM AQ1210-01EN

Setting Up the OTDR Feature

App

Index

Report Format

Measure Conditions (Job Information)

The following information is included.

Label

Originating Loc

Company Name

Terminating Loc

Name

Current Data Flag

Fiber ID

Supplier Name

Fiber Type

Model Name

Cable ID

Unit Name

Cable Code

FW Ver.

*1, *2

1 Automatically included by the instrument

Report creation date and time

2 Firmware version

Information such as label and company name can be specified on the Label Setup screen explained

in “Setting Labels.” Set these if necessary.

Measured Results (Link Summary)

The following information is included.

•  Total distance
•  Total loss
•  Total return loss
•  Number of events
•  Fault events
•  Pass/fail judgments
•  Measured date

Map, Waveform, Marker Information, Measurement Conditions, and Overview

These are included as shown below.

Map

Waveform (Trace)

Marker

information

Overview

Measurement

conditions

2.4 File Conditions

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands