YOKOGAWA AQ1215A User Manual Download

Page: 117 / 282

6-9

IM AQ1210-01EN

Analyzing W

aveforms

App

Index

6 Point Markers

Tap the

6 Point Markers

soft key. A soft key menu for the 6 markers method appears.

Marker

Sets marker

Places marker at the

cursor position

Sets marker

Places marker at the

cursor position

Return loss

Splice loss

Set marker Y2.

Places marker Y2 at the

cursor position

Sets marker

Places marker at the

cursor position

Marker Y2

Marker

See “2 Point Markers

(when the marker

mode is Marker)”

Marker Y1

Marker Y3

Set marker Y1.

Places marker Y1 at the

cursor position

Set marker Y3.

Places marker Y3 at the

cursor position

Note

• Set the markers in the order shown above, starting with the measurement start point (the distance

reference).

• The measured loss value differs depending on the specified approximation method.
• Set the correct position for

. The splice loss changes greatly depending on the position of

6.1 Operating Cursors and Markers

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands