YOKOGAWA AQ1215A User Manual Download Page 118

Page: 118 / 282

6-10

IM AQ1210-01EN

5 Point Markers (when the marker mode is Line)

Tap the

5 Point Markers

soft key. A soft key menu for the 5 markers method appears.

Marker n

Splice loss

Marker N

Marker E

Marker F

Marker f

Select the marker you

want to control

(C, n, N, E, F, f).

Press this soft key to select

the marker that you are

operating. When you tap on

the data screen or turn the

rotary knob, the selected

marker or cursor appears

that you can move.

Press to set all markers

together.

Sets all markers at once.

Set the cursor link

(OFF, ON).

See “2 Point Markers

(when the marker mode

is Marker)”

Set the approximation

method.

See section 2.3.

Note

• Set the markers in the order shown above, starting with the measurement start point (the distance

reference).

• The measured loss value differs depending on the specified approximation method.
• Set marker E to the correct position. The splice loss changes greatly depending on the position of E.

4 Point Monitor (splice loss at two locations)

Tap the

4 Point Monitor

soft key to display the 4 Point Monitor soft key menu.

Place markers and for

monitoring the first event.

Place markers and for

monitoring the second event.

Sets marker

Places marker at the

cursor position

Sets marker

Places marker at the

cursor position

Sets marker

Places marker at the

cursor position

Sets marker

Places marker at the

cursor position

Clears the marker

display

Levels of each marker

Splice loss

between and

Splice loss

between and

6.1 Operating Cursors and Markers

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

YOKOGAWA AQ1215A, User Manual, Page: 118 / 282

Search results

Summary of Contents for AQ1215A

Reviews: