YOKOGAWA AQ1215A User Manual Download | Manualshive

Page: 30 / 282

background image

1-24

IM AQ1210-01EN

Multicore Loss Test

You can efficiently measure multicore optical fiber cable and optical line degradation.

Projects

Projects are group of items for measuring multi-core fibers.
This feature is the same as that explained in “Optical Pulse Measurement of Multi-core Optical Fiber

Cables” on page 1-21.

• Number of Fibers, Number of Fibers in Each Division, Tape Number

The core number indications and settings vary depending on the type of multi-core fiber cable.
These features are the same as those explained in “Optical Pulse Measurement of Multi-core

Optical Fiber Cables” on page 1-21.

Master and Slave

Connect two instruments and specify the optical power meter as the master and the light source

as the slave. You can also use the AQ1100/AQ1200A/AQ1200B/AQ1200C/AQ1200E/AQ1205A/
AQ1205E/AQ1205F in the multi-field tester series instead of this instrument as the master or slave.
The preparation involves the following steps.

• Connecting an Optical Fiber Cable for Signal Transmission (step 1)

To transmit, between the master and slave, project setup information and information about the

fiber under loss test, you must specify a fiber cable from the multi-core optical fiber cable to use
for the signal transmission. Connect one end of the optical fiber cable for signal transmission to
the OTDR port (PORT1) of the instrument specified as the master (optical power meter side) and
the other end to the OPM port of the instrument specified as the slave (light source side).

• Transferring Object Information from the Master to the Slave (step 2)

On the master instrument, create a project. Transfer the project information to the slave

instrument through the optical fiber cable for signal transmission.

AQ1210A, AQ1215A,

AQ1210E, AQ1215E,

AQ1215F, AQ1216F

AQ1210A, AQ1215A,

AQ1210E, AQ1215E,

AQ1215F, AQ1216F

Master (this instrument)

Create a project

Slave (this instrument)

Optical fiber cable for signal transmission

OTDR port (PORT1)

OPM port

Transfer the project data

• Connecting the Optical Fiber Cable to Perform Multi-Core Loss Test On (step 3)

Multi-core loss test is performed on all optical fiber cables other than the optical fiber cable for

signal transmission. Connect one end of the optical fiber cable to be tested to the OPM port of
the master instrument and the other end to the OTDR port (PORT1) of the slave instrument.

1.7 Application

«
...
28
29
30
31
32
...
»

Summary of Contents for AQ1215A



























































































































































































































































































Reviews:

No comments

Related manuals for AQ1215A

Brand: Keiser Pages: 2

Brand: ECA Pages: 3

Brand: Nautilus Pages: 12

medialon Showmaster Go

Brand: 7th Sense Pages: 9

Brand: olympia electronics Pages: 4

Brand: Panasonic Pages: 23

GED5000IL Series

Brand: Zimmer Pages: 52

Brand: K-SPORT Pages: 5

Brand: Ocean Signal Pages: 2

RadioPRO 4 RP4-MZ11

Brand: PAC Pages: 5

BOMAG BVP 12/50 A

Brand: Fayat Pages: 105

HALO miniLUME LA5300

Brand: Cooper Lighting Pages: 2

Brand: Free The Tone Pages: 8

Brand: Perel Pages: 26

Brand: Land Pride Pages: 72

Brand: Nuvo Pages: 2

Brand: unix Corporation Pages: 6

Brand: B-Safety Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands