manualshive.com logo in svg

YOKOGAWA AQ1215A, User Manual

The YOKOGAWA AQ1215A user manual is essential for operating your device efficiently. Easily accessible and free to download from manualshive.com, this comprehensive manual provides step-by-step instructions and valuable insights to ensure a seamless user experience. Empower yourself with the knowledge to maximize the potential of your AQ1215A with this user manual.

Share
Download
background image

1-25

IM AQ1210-01EN

Features

1

2

3

4

5

6

7

8

9

10

11

App

Index

 

Executing the Multi-Core Loss Test

  First, start the multi-core loss test on the master instrument. The core number information of the 

cores to be tested is transmitted from the master side through the optical fiber cable for signal 
transmission. When the core numbers to be measured are received through the OPM port, the 
slave instrument will be ready to execute a multi-core loss test.

  Execute the multi-core loss test on the slave side. The light to be measured is output from the 

OTDR port (PORT1) on the slave side. This light enters the OPM port on the master side, and 
the loss in the optical fiber cable with the target core number is measured.

  The measurement results are sent from the master to the slave instrument through the optical 

fiber cable for signal transmission.

  

 

AQ1210A, AQ1215A, 

AQ1210E, AQ1215E, 

AQ1215F, AQ1216F

AQ1210A, AQ1215A, 

AQ1210E, AQ1215E, 

AQ1215F, AQ1216F

Master (this instrument)

Execute a multicore loss test

Slave (this instrument)

Optical fiber cable for signal transmission

OTDR port (PORT1)

OPM port

Transfer the results of the multicore loss test

Optical fiber cable under 

multicore loss test

OTDR port 

(PORT1)

OPM port

Light being measured

  If you cancel an ongoing multi-core loss test, the completed portion of the measurement results 

are held, so you can resume the test from the optical fiber cable with the next target core 
number.

Advanced Analysis

Multi Trace Analysis

  You can load up to four waveforms that have been measured on the instrument and display 

them simultaneously for comparison. You can adjust the vertical display position of each loaded 
waveform.

  

Trace 1

Trace 2

Trace 3

Trace 4

Displays up to four waveforms simultaneously

You can move a waveform over another waveform to compare the two.

1.7  Application

Summary of Contents for AQ1215A



























































































































































































































































































Reviews:

No comments

Related manuals for AQ1215A

FagronLab FG User Manual preview
FG
Brand: FagronLab Pages: 16
Bard PowerGlide Patient Manual preview
PowerGlide
Brand: Bard Pages: 36
Bard Excalibur Instructions For Use preview
Excalibur
Brand: Bard Pages: 2
Bard Site-Rite 5 Technical Manual preview
Site-Rite 5
Brand: Bard Pages: 30
Bard Peripheral Vascular True Instructions For Use Manual preview
True
Brand: Bard Peripheral Vascular Pages: 44
Ultimate Healthcare Tamora Plus II Quick Reference Manual preview
Tamora Plus II
Brand: Ultimate Healthcare Pages: 2
Ultimate Healthcare Cura II User Manual preview
Cura II
Brand: Ultimate Healthcare Pages: 40
Wacker Neuson BS Operator'S Manual preview
BS
Brand: Wacker Neuson Pages: 34
DAAB DB409 Instruction Manual preview
DB409
Brand: DAAB Pages: 12
ASIA TECHNOLOGY AF-300 Operating Manual & Parts List preview
AF-300
Brand: ASIA TECHNOLOGY Pages: 38
PALAZZANI RAGNO TSJ 30.1 Operation And Safety Manual preview
RAGNO TSJ 30.1
Brand: PALAZZANI Pages: 131
Exitronix VEX-WPCR Series Installation Instructions preview
VEX-WPCR Series
Brand: Exitronix Pages: 4
Medivators ADVANTAGE 78400-117 Maintenance Instructions Manual preview
ADVANTAGE 78400-117
Brand: Medivators Pages: 12
SMP Playgrounds CAPE HORN EC202B Installation Instructions Manual preview
CAPE HORN EC202B
Brand: SMP Playgrounds Pages: 22
Bandit INTIMIDATOR 15XPC Operating & Parts Manual preview
INTIMIDATOR 15XPC
Brand: Bandit Pages: 112
Qtx B12P User Manual preview
B12P
Brand: Qtx Pages: 6
Olimpia electronics RT-52/HACCP Quick Start Manual preview
RT-52/HACCP
Brand: Olimpia electronics Pages: 2
CA.MI O2-easy Instruction Manual preview
O2-easy
Brand: CA.MI Pages: 96

Brands by name

Popular brands

Load more brands