manualshive.com logo in svg

YOKOGAWA AQ1215A, User Manual, Page: 94 / 282

Share
Download
YOKOGAWA AQ1215A User Manual Download Page 94

5-1

IM AQ1210-01EN

Analyzing Events

1

2

3

4

5

6

7

8

9

10

11

App

Index

5.1  Analyzing in TRACE Mode

Procedure

Waveform Data Display

1.

 Press 

MENU

 to display the MENU screen.

For details on the MENU screen, see the Getting Started Guide, IM AQ1210-02EN.

2.

 Tap 

OTDR

 to display the OTDR screen.

•  Switching the Display between TRACE Mode and MAP Mode

3.

  Tap the 

TRACE

/

MAP

 button to set the data display screen to TRACE mode.

When the data display screen is in TRACE mode, the button is MAP.

 

  

•  Displaying Waveform Data

4.

 Press 

AVG

. The measurement begins, and the data display screen shows the waveform.

 

When averaged measurement is completed, event analysis is automatically executed, and 

the event analysis results are shown on the data display screen. For details on averaged 

measurement, see section 4.1.

Note

If you display waveform data using the following methods, you need to manually execute event analysis. See 
“Soft Key Menu (during event analysis)” explained later.
•  When a real-time measurement is performed
•  When waveform data (without event analysis information) is loaded from a USB memory device or 

internal memory Event analysis information is not included in waveform data of real-time measurement or 
waveform data of averaged measurement that is aborted in the middle of a measurement.

Displaying Event Analysis Results

 

  

Measurement reference point: S

Event No.

Event detected as the end of the optical fiber cable: E

List of events

Displayed by tapping the 

List tab.

Chapter 5  Analyzing Events

Summary of Contents for AQ1215A



























































































































































































































































































Reviews:

No comments