YOKOGAWA AQ1215A User Manual Download Page 214

Page: 214 / 282

8-43

IM AQ1210-01EN

Using the

Application Feature

App

Index

Sharing the Project Conditions

Send the project conditions created on the master side to the slave side.

Connect the OTDR port (PORT1) of the instrument on the master side and the OPM port of the

instrument on the slave side with an optical fiber cable.

AQ1210A, AQ1215A,

AQ1210E, AQ1215E,

AQ1215F, AQ1216F

AQ1210A, AQ1215A,

AQ1210E, AQ1215E,

AQ1215F, AQ1216F

Master

Create a project

Slave

Optical fiber cable for signal transmission

OTDR port (PORT1)

OPM port

Transfer the project data

On the slave side, tap the

Receive Project from Master

soft key. The soft key changes to “Stop.”

10.

On the master side, tap the

Project Transmission START

soft key.

Slave

Master

Receives project conditions from the master

Sends project conditions to the slave

When the transmission of the project conditions is completed between the master side and slave

side, a screen appears for executing multicore loss tests.

8.4 Performing a Multicore Loss Test (Multicore Loss Test)

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

YOKOGAWA AQ1215A, User Manual, Page: 214 / 282

Search results

Summary of Contents for AQ1215A

Reviews: