YOKOGAWA AQ1215A User Manual Download Page 101

Page: 101 / 282

5-8

IM AQ1210-01EN

• Fixing Events

Event positions can be fixed. Fixed events are handled as master events. You can configure the

Instrument so that in subsequent event analysis only master events are handled.

Tap the

Event Fix

soft key to display an Event Fix Mode screen.

Master mode

Registers the current placed event as the master.

New events are not detected even when the waveform data is updated.

Only the master event is displayed on the updated waveform data.

Add mode

Registers the current placed event as the master.

New events are detected when the waveform data is updated.

Both the master event and the new detected events are displayed

on the updated waveform data.

Events are not fixed.

5.1 Analyzing in TRACE Mode

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands