YOKOGAWA AQ1215A User Manual Download

Page: 65 / 282

2-27

IM AQ1210-01EN

Setting Up the OTDR Feature

App

Index

Setting Comments

Tap

Comment Setup

to display the Comment Setup screen.

Set a comment (up to 30 characters).

Enter a comment by following the procedure provided in “Entering Text”

in the Getting Started Guide, IM AQ1210-02EN.

Setting Labels

Tap

Label Setup

to display the Label Setup screen.

Label, Company Name, Name, Cable ID, Fiber ID, Cable Code, Originating Loc (A),

Terminating Loc (B)

Enter a comment by following the procedure provided in “Entering Text” in the Getting Started

Guide, IM AQ1210-02EN. You can enter up to 36 characters.

Select the check box to use the file

ID (ID number) as the fiber ID. For

details on ID numbers, see “Setting

the File Name” on page 2-24.

Set the fiber type (652:Conventional SMF, 653:Dispersion Shifted SMF,

654:Cut-Off Shifted SMF, 655:Non-Zero Dispersion Shifted SMF, 656:NZDSF

for Wideband Transport, 657:Bend Optimized SMF, 651:Multi-Mode Fiber).

Set the current data flag

(BUILT (BC), REPAIRED

(RC), OTHER (OT), and

CURRENT (CC)).

Direction (A -> B, B -> A)

Shows from which side the optical

fiber cable connecting the start

position (A) and stop position (B) was

measured.

2.4 File Conditions

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands