YOKOGAWA AQ1215A User Manual Download

Page: 210 / 282

8-39

IM AQ1210-01EN

Using the

Application Feature

App

Index

Multicore Loss Test Screen

Master

Slave

Before loading project conditions (setup)

After loading project conditions (setup)

A screen for executing multicore loss tests

Project condition status

• Project Condition Status

Before starting a multicore loss test, set the conditions (e.g., number of cores) of the multi-core

fiber cable to be measured. The project conditions are created on the master side and then sent
to the slave side.

On the slave side, the project conditions sent from the master side are received and loaded into

the instrument.
Setting: Indicates that the master and slave are being selected or the project information is

being created.

Sending: Indicates that the project conditions are being sent from the matter side to the

slave side.

Receiving: Indicates that the project conditions sent from the master side are being received

on the slave side.

Complete: Indicates that the transmission of the project conditions has been completed

between the master side and slave side. After completion, a screen appears for
executing multicore loss tests.

8.4 Performing a Multicore Loss Test (Multicore Loss Test)

Summary of Contents for AQ1215A



























































































































































































































































































Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands

YOKOGAWA AQ1215A, User Manual

Search results

Summary of Contents for AQ1215A

Reviews:

Related manuals for AQ1215A

Brands by name

Popular brands